TREADIVO.

Rolling out across Australia

Choose your location.
Back to blog

4x4 Tyre Pressure Guide for Australia: Road, Off-Road and Towing

Illustrated 4x4 tyre pressure guide title card

The right 4x4 tyre pressure is not one number. It starts with the placard on your vehicle for sealed roads, drops in steps as the terrain gets softer or rougher, and rises at the rear when you tow. Most wagons and utes sit between 200 and 250 kPa (29 to 36 psi) on bitumen, and off-road starting points run from about 32 psi on gravel down to the mid-teens on soft sand. Every drop in pressure has to be matched with a drop in speed, and every trip ends with a reinflate.

This guide gives you the starting figures, the reasoning behind them and the habits that keep tyres intact. It is written for drivers who want to get on with the trip, and for anyone who wants the tyres under the vehicle to be the right ones for the job.

Treadivo
Find tyres suited to your 4x4
Search by vehicle or tyre size, compare transparent pricing and choose a local fitter for your next set of tyres.

TL;DR

  • On sealed roads, run the pressures on your tyre placard (glovebox, door pillar or engine bay). Most wagons and utes land at 200 to 250 kPa (29 to 36 psi), cold.
  • Off-road starting points: gravel and corrugations 26 to 32 psi, rock 18 to 26 psi, mud 16 to 28 psi, soft sand mid-teens. Treat them as starting points, not fixed rules.
  • Lower pressure means lower speed. Going below about 15 psi (100 kPa) is for emergencies and recovery only.
  • Towing: the tow vehicle’s rear tyres need more pressure, and the caravan or trailer follows its own plate. A weighbridge gives the real answer.
  • Reinflate as soon as you are back on hard roads, then check the tyres, valves and dust caps.

Table of Contents

Start with the placard, not a chart

Every pressure on every chart starts from a baseline, and that baseline is your vehicle’s tyre placard. Transport for NSW says every vehicle built since 1973 carries a placard in the glovebox, engine bay or door pillar, listing tyre sizes, load capacity, speed rating and pressure. If you can’t find it, the owner’s manual has the same figures.

4x4 Australia’s 4WD trainer David Wilson says most wagons and utes run 200 to 250 kPa (29 to 36 psi) on bitumen, and that placards list higher pressures for a loaded vehicle. He also warns that over-inflation wears tyres prematurely, raises puncture risk and lengthens emergency braking distances.

Two cases need extra thought:

  • Aftermarket light truck (LT) tyres. LT tyres have stiffer, heavier-duty construction, so the placard pressure written for the original passenger-style tyre may not suit them. The same 4x4 Australia advice notes LT tyres may need adjusted pressures.
  • Changed wheels, tyres or weight. Once you add a bar, a canopy, water tanks or a different tyre, the original figure is a starting point only. The most accurate way to set pressures is to weigh each axle at a weighbridge and work from those weights.

If you are changing tyre size, check that the new tyre still meets the load rating the vehicle needs. Our guides on reading and choosing 4x4 tyre sizes and on what a load index means per tyre cover the numbers on the sidewall.

Setting road pressures properly

Check pressures when the tyres are cold. Queensland’s TyreSmart guidance, as relayed by industry sources, treats tyres as cold after sitting for around three hours or driving no more than 2 km. Heat from driving raises the reading, so never let air out of a warm tyre to hit the cold figure.

A handy cross-check is the 4 psi rule. 4x4 writer Robert Pepper describes it this way: pressures typically climb about 4 psi from cold after a stretch of bitumen driving. In a Practical Motoring reader answer he put it at 3 to 4 psi after about 20 minutes on a moderately temperate day. If the tyres gain much more than that, they are likely running too low for the load. If they gain almost nothing, they may be overinflated.

Pepper’s broader point is useful too: there are no absolute pressures, only principles and examples, and the gap between 34 and 36 psi makes no real difference. Aim for the right zone, check regularly, and don’t chase a single digit.

Check the spare as well. It is the tyre most often forgotten, and it is the one you will rely on a long way from help.

Setting road pressures properly

Off-road starting pressures by terrain

The figures below come from Australian 4WD publications and trainers. They differ because vehicles, loads and tyres differ, so read them as a range and begin at the higher end of it.

Terrain Typical starting range Notes
Sealed road Placard, often 29 to 36 psi Cold pressures, set for your load
Gravel and corrugations 26 to 32 psi Keep speed to 80 km/h at most
Rocky tracks 18 to 26 psi LT tyres can start around 22 psi
Mud 16 to 28 psi Depends on tyre construction and clay
Soft sand 14 to 18 psi Lower only if you are still struggling

Where these numbers come from:

  • Gravel and corrugations. Practical Motoring’s Steve Cassano suggests 26 to 32 psi, about 75 per cent of normal road pressure, never above 80 km/h and often 20 to 30 km/h on the worst stretches. Eureka 4WD, an off-road training business, runs 26 psi over corrugations and describes the tyres as acting like an extra shock absorber that protects both occupants and the suspension.
  • Rock. Eureka 4WD gives 18 to 22 psi over rocky ground. 4x4 Australia suggests around 22 psi for rock crawling with LT tyres. Lower pressure lets the tyre mould over sharp edges, which matters most on lower-profile tyres.
  • Mud. Eureka gives 16 to 20 psi depending on tyre construction, and 4x4 Australia suggests about 22 psi in deep, baseless mud.
  • Sand. 4x4 Australia suggests going down to around 16 psi in soft sand, and Eureka runs 14 psi, with work vehicles at 10 to 14 psi.

Sand is the terrain where drivers most often go too low. Heavier vehicles, big loads and tall sidewalls all change the answer. Start at the top of the range, test the traction, and only step down in small amounts.

The 20 per cent rule for dirt roads

A simple way to remember it, from David Wilson in 4x4 Australia: on dirt roads, let out about 20 per cent of the placard pressure and reduce speed by about 20 per cent. As the terrain gets rougher, keep stepping down, and match each pressure drop with a lower speed so the tyres do not overheat.

For a placard of 36 psi, that is around 29 psi on a good dirt road, which sits just under the corrugation range above. It is a sensible first move before you decide whether the track needs more.

Dirt-road pressure and speed reduction example

Airing down safely

Pressure, load and speed are linked. Lowering pressure on a loaded vehicle makes the tyre flex more, which builds heat. That is why every air-down recommendation comes with a speed limit.

Build these habits into every trip:

  1. Drop gradually. 4x4 Australia advises stepping down in stages with lower speed, and holding a minimum of 100 kPa (15 psi) except in emergencies.
  2. Watch the sidewalls. As the sidewall bags out at low pressure, sharp rocks and roots become the main risk. On rocky tracks, the fix is better line choice: keep sidewalls clear and put the tread on the rock, as DownThunder’s guide explains.
  3. Brake and steer gently. A deflated tyre has a softer sidewall and a looser grip on the rim. Smooth inputs keep the bead seated.
  4. Know the limits of low pressure on dirt roads. Running very low pressures on a fast unsealed road is a common cause of bead damage and tyre failure, so air back up when speeds rise.

If you want to know what a bead leak looks like and what to check, our guide to tyre bead leaks and the checks that take 15 to 20 minutes is a good read before a big trip.

Reinflating after the trail

The trip is not over until the tyres are back at road pressure. 4x4 Australia advises reinflating to on-road pressures once you are back on the blacktop, inspecting for damage, checking valve stems and refitting dust caps. Skipping this step affects handling and braking, and a tyre running low at highway speed can overheat quickly.

A good post-trail routine:

Some parks publish a recommended figure and provide a tyre pressure station near the exit, so look out for them on the way in and out of sand areas.

Towing tyre pressure

Towing changes the load on the tow vehicle’s rear axle, and that changes the pressure it needs. Towball mass counts as vehicle weight. Pepper notes that 150 kg or more of towball mass significantly increases rear axle load, which calls for more rear pressure. Front pressures generally do not need to rise, because the front axle is carrying less.

A workable approach in three parts:

  1. Tow vehicle. Use the placard figure for the loaded or maximum-load condition. The South Australian caravan industry towing guide says to use the tow vehicle’s placard pressures for normal and maximum load, and to find the optimum pressure from the fully laden weight at a weighbridge.
  2. If the placard has no separate towing figure. UK tyre safety body TyreSafe suggests setting the rear tyres at the fully laden pressure, or 4 to 7 psi higher if the loaded figure matches the normal one. That is UK guidance, so treat it as a reasonable starting point and confirm with a weighbridge reading.
  3. Caravan or trailer. Follow the manufacturer’s plate or tyre information for the van, not the tow vehicle’s placard.

Always check and adjust when cold, and never reduce a warm tyre to hit the number. If you tow off-road, the same speed-and-pressure logic applies to the trailer tyres as to the vehicle: deflate for soft sand, drive slowly, and reinflate when you are back on firm ground.

Towing also raises the stakes on load rating. A replacement tyre must carry a load rating equal to or higher than the original, which is why the load index matters when you choose tyres for a tow vehicle.

The gear that makes it work

Pressure management only works if you can measure and change it. A reliable kit is small:

  • A quality pressure gauge. Analogue gauges can be found for under $20 each, according to Practical Motoring, and a spare is cheap insurance.
  • A tyre deflator or a four-way valve tool, which Practical Motoring puts at around $30.
  • A good air compressor with enough hose to reach all four wheels and the trailer.

Carry the kit where you can reach it without unpacking the vehicle. Check the gauge against a second one now and then, because a gauge that reads 3 psi out is worse than none.

Is your tyre right for the pressures you plan to run?

Pressure advice assumes tyres in good condition and suited to the job. Highway tyres, all-terrain tyres and mud-terrains behave differently when aired down: tread depth, sidewall construction and load rating all change how much you can safely drop. Our comparison of highway versus all-terrain tyres in Australia shows how the choice affects grip and stopping distances.

If you are not sure your size matches your vehicle’s limits, calculating a compliant tyre size is the first step, and a tyre size calculator does the arithmetic for you.

Tyres, fitted locally

We built Treadivo for drivers who want the right tyres without the runaround. You can search by vehicle model or tyre size, browse our SUV and 4x4, light truck, mud terrain and highway ranges, pick a local fitter, and check out in about three minutes, with same-day fitting confirmation. Pricing is transparent and itemised, with no hidden fees. Our AR tool lets you see how a tyre looks on your vehicle first, and our AI tread check tool helps you assess the tyres you have now.

Fitters are available in Perth and Melbourne, and a fresh set of tyres fitted by someone who sets the correct pressure is the best start to any trip.

Treadivo

Not sure what fits? Our guide to finding tyres for your car using rego lookup takes you through it.

Our view: pressure is a tyre decision, not just a trip decision

Most pressure advice treats the tyre as a given. We think it works the other way around. The pressures you can safely run depend on the tyre’s size, load index and construction, so the best time to think about pressure is when you choose the tyre.

A tyre with the right load rating for your loaded vehicle and your tow weight gives you a wider, safer window to work in, whether that is highway cruising, corrugations or soft sand. A tyre that is a little too small for the job leaves you guessing.

That is why we put sizes, load ratings and fitment checks front and centre, and why we give you a local fitter and a confirmed booking rather than leaving you to sort it out. Our tools, from the size calculator to the AI tread check, exist so you can see what you are running before you head out.

Set the tyres up right, weigh the vehicle if you are loaded or towing, air down in steps, and always air back up.

Areesh

FAQ

What is a good tyre pressure for a 4x4 on the road?

Use the placard on your vehicle, set when the tyres are cold. Most wagons and utes run 200 to 250 kPa (29 to 36 psi), with the higher placard figure for a fully loaded vehicle. Aftermarket LT tyres may need a slightly different pressure, so confirm it for your setup.

What tyre pressure should I use for sand?

Start around 15 to 18 psi for general sand driving and step down towards the mid-teens only if you need to. Heavy loads and heavier vehicles need more pressure, not less. Keep speed low, and stay at or above 15 psi (100 kPa) unless you are recovering a stuck vehicle.

How much should I increase tyre pressure when towing?

Use the placard figure for a loaded vehicle at the rear, or follow the manufacturer’s towing figure if one is given. Where there is none, UK guidance suggests adding 4 to 7 psi at the rear. A weighbridge reading of your actual axle loads is the most reliable answer.

Do I need to reinflate after going off-road?

Yes, as soon as you are back on firm, fast roads. Low pressures overheat tyres at speed and can damage the bead. Inspect the tyres, check valves and caps, and reset to your road pressure before you drive home.

Sources

Ready for new tyres?

Search your tyre size and see live prices, with fitting or pickup anywhere in Australia.